parameters defined by Ron Ghosh

 values chosen for LAMP

   1

 contents of PRESET 1 (1/100 s if time)

 x

   2

 contents of PRESET 2 (generally not used)

 x

   3

 time [1/10 s] scaler 1

 x

   4

 total detector counts (scaler 2)

 (not necessary for LAMP)

   5

 total monitor counts (3)

 x (but this one)

   6

 total number of selector revolutions (4)

   7

 total number of chopper revolutions (5)

   8

   9

  10

  11

  12

  13

  14

  15

 detector angle (calc.) [deg.]

 x

  16

 coder 1: beamstop pos. By [mm]

 x

  17

 coder 1: beamstop pos. Bx [mm]

 x

  18

 c. 3: sample changer/translat. STR [mm]

 x

  19

 c. 4: detector distance DET (read) [m]

 x

  20

 selector speed [1/min] (last)

  21

 chopper 1 speed [1/min]

  22

 chopper 2 speed [1/min]

  23

 digital voltmeter channel 1

  24

 digital voltmeter channel 2

  25

 selector type (1., 2. etc.)

  26

 sample-detector distance (calc.) [m]

 x

  27

 run sequence: cycle

  28

 run sequence: serial

  29

 temperature set point [K]

  30

 regulation temperature [K]

  31

 sample temperature [K] (last)

 x

  32

 temperature control off/on (0./1.)

  33

 value of IEEE-1 at start

 x

  34

 value of IEEE-1 at end

 x

  35

 ... further IEEE values

  36

  37

  38

  39

  40

  41

  42

  43

  44

  45

  46

  47

  48

  49

  50

 further parameters stored with the data

  51

 beam centre address X0 [cell#]

 x

  52

 beam centre address Y0 [cell#]

 x

  53

 wavelength []

 x

  54

 relative wavelength resolution

 x

  55

 detector pixel size x [mm]

 x

  56

 detector pixel size y [mm]

 x

  57

 alarm status no alarm/alarm 0/1

  58

 collimation [m]

 x

  59

 attenuator type (1., 2. etc.)

  60

 attenuator out/in (0./1.)

  61

 detector angle (read) [deg.]

 x

  62

 detector translation (read) [mm]

 x

  63

 selector angle [deg.]

 x

  64

 sample distance [mm]

 x

  65

 sample rotation [¡]

 x

  66

 changer position #

 x

  67

 sample height [mm]

 x

  68

 source ap. left [mm]

  69

 source ap. right [mm]

  70

 source ap. lower [mm]

  71

 source ap. upper [mm]

  72

 source ap. distance [m]

  73

 sample aperture hor. /diam. [mm]

  74

 sample aperture vert. or 0. [mm]

  75

 beamstop width or diameter [mm]

  76

 beamstop height or 0. [mm]

  77

 ISUM X1 [cell #]

  78

 ISUM X2 [cell #]

  79

 ISUM Y1 [cell #]

  80

 ISUM Y2 [cell #]

  81

 shear speed [1/min]

  x

  82

 magnetic field [Tesla]

  83

 pressure [Pa]

  84

 reactor power [MW]

  85

 TOF: # of channels

  86

 TOF: delay [ms]

  87

 TOF: channel width [ms]

  88

 TOF: channel increment factor

  89

 preset flag mon./time (0/1)

  90

 TOF: # of current frame

  91

 data file version number

  92

 iris position #

  93

 ADC1

  94

 ADC2

  95

 ADC3

  96

 ADC4

  97

 DAC1

  98

 DAC2

  99

 DAC3

 100

 DAC4

 101

 Sample table translation (TTR) [mm]

 102

 Sample goniometer angle (CHI) [deg.]

 103

 Ampere (magnet power supply)

 104

 Voltage (magnet power supply)

 105

 TOF/kin current channel start time

 106

 Flipper frequency

 107

 Flipper amplitude

 108

 Flipper pickup

 109

 Polarisation

 110

 TOF/kin current channel centre (time)

 111

 Current of (new) power supply 1 (Amp1)

 112

 Voltage of power supply 1 (Volt1)

 113

 Current of (new) power supply 2 (Amp2)

 114

 Voltage of power supply 2 (Volt2)

 115

 Current of (new) power supply 3 (Amp3)

 116

 Voltage of power supply 3 (Volt3)

 117

 Magnet Frequency (AW)

 118

 Magnet Amplitude (AW) (Volt)

 119

 120

 121

 122

 123

 124

 125

 126

 127

 128